O W N E R ' S
M A N U A L
P/SP-1500 AV Processor/Preamplifier
P/SP-1500 Owner's Manual
3
Setting Up Your Home Theater System
Refer to Diagram on Page 4
Speaker Placement
Proper speaker placement is essential for optimum performance of your home theater system. Improper
placement of speakers can produce an unnatural sound and greatly diminish the home theater
experience. Here are some basic guidelines for speaker placement based upon idealized conditions.
However, it may be necessary to make compromises for furniture, windows, doorways, and other
aesthetic reasons.
Front Speakers
Try to locate your front left and right speakers an equal distance from your television monitor or
projection screen. Ideally, your viewing/listening position should be at the point of an equilateral
triangle with the left and right speakers at the other points.
Center Speaker
The center speaker’s main function is to reproduce dialog and to join the sonic image from the speakers
with the visual image on the screen. It is best to place your center speaker directly above or below the
television monitor for a more realistic effect. The distance from your listening position to the center
channel speaker should be the same distance as from your listening position to the left and right
speakers. This necessitates placing the center speaker somewhat behind the left and right speakers. This
placement assures the sound from all three front speakers will arrive at your listening position at
precisely the same time. If you are using a direct view television with a picture tube, we strongly
recommend a shielded center channel speaker if you intend to locate it near the monitor. The magnetic
field of an unshielded speaker will cause an extreme discoloration of most direct view TV screens. If
you are placing your front speakers behind a high-quality perforated projection screen, locate your center
speaker at the same height as your left and right speakers.
Conventional Surround Speakers
Surround speaker placement is a little more flexible than the front speakers. In the Dolby Pro Logic and
even Dolby Digital (AC-3) mode surround speakers are intended to create a more diffuse ambient effect
rather than a precise sonic image. To avoid drawing your attention away from the action on the screen,
you should not be able to localize the sound coming from your surround speakers. Therefore, you
should try to avoid pointing the surround speakers directly toward your listening position and place them
behind you and at least three feet above your ear level when you are seated. You may even want to try
aiming them at the wall or ceiling for a greater ratio of reflected to direct sound to help reduce
localization. Experimentation with surround speaker placement is often required to yield optimum
results.
THX Dipole Surround Speakers
THX certified dipole surround speakers are designed for superior surround channel performance. If you
are using THX Home Cinema front and rear firing dipole surround speakers, locate them at least two
feet above and to the sides of your listening area. This places you in the “null” of the dipole speakers to
minimize localization of the surround speakers.
Subwoofer
The best way to position your subwoofer is to first hook it up and place it close to your listening
position. Next, stand in various spots within your room and find the location that will give you the
strongest and most balanced bass without excessive boominess. Once you have found the optimum
location, simply relocate the subwoofer to that spot.
4
P/SP-1500 Owner's Manual
L. Surr
R. Surr
Typical home theater setup using THX dipole surround speakers.
Note that all three front speakers are the same distance to the listening area.
L. Surr
R. Surr
Typical home theater setup using conventional surround speakers
Note that all three front speakers are the same distance to the listening area
P/SP-1500 Owner's Manual
5
Making Connections to Your P/SP-1500
Refer to Diagram on Page 6
Input Connections
Before making any connections to your P/SP-1500, be sure to turn off the power to your amplifiers.
Also, make sure there is no strain or tension on any connections that could make them pull loose.
Audio/Video Input Connections
Your P/SP-1500 comes equipped with four audio/video line inputs, three audio-only inputs, plus a six
channel discrete input for an external digital surround adaptor. All seven inputs are compatible with any
typical analog line level source such as a compact disc player, digital to analog converter, tuner, tape
deck, or the audio output of a laser disc player or video cassette recorder. The four audio/video inputs
also have switching capability for both NTSC composite video or S-video. You may use just the audio
jacks of any of the audio/video inputs if your system needs to accommodate more audio than video
source components.
Video Inputs 1-3 (Playback Only)
Connect the audio and video outputs of any audio/video source such as a laser disc player, video cassette
recorder, satellite receivers, etc. to these inputs. This input has accompanying S-video or composite
video connections, but it does not provide an audio/video record output. If your video cassette recorder
has only a mono output you can use either the left or right audio input jack of your P/SP-1500.
However, the internal circuitry will not produce surround effects from mono signals.
Video Input 4 (Record and Playback)
Use this input for to the video cassette recorder you also intend to use for recording. The Video 4 input
has accompanying composite and S-video switching and full audio/video recording output capability.
Its record input accepts signals from any of the other six line inputs. Connect the left and right audio
output connectors from the video cassette recorder you will use for recording to the Video 4 Play
connectors of the P/SP-1500. Next, connect the left and right audio input connectors of the video
cassette recorder you will use for recording to the Video 4 Rec connectors of the P/SP-1500.
Audio 1-3 (Audio Only)
Connect a line level source to these audio-only inputs such as a compact disc player, digital to analog
converter, tuner, or tape deck.
S-Video and Composite Video Connections
Your P/SP-1500 has both composite RCA and S-video circuits with separate video amplifiers for each of
the four audio/video inputs. If you connect a video signal to one of the RCA composite input
connectors, the signal will only be available through the RCA composite Monitor and Video 4 Record
output connectors. Likewise, if you connect a video signal to the S-video input, the video signal will
only be available through the S-video Monitor and Video 4 Record output connections.
Connecting the Television Monitor or Video Projector
Connect the RCA composite or S-video Monitor output connector of your P/SP-1500 to the input
connector of your monitor or projector. If you have a monitor with a separate S-video and composite
inputs, connect the P/SP-1500 S-video output to one of the monitor’s inputs (such as External 1) and the
composite output to another input (such as External 2). This way, you can view both composite or S-
video sources by selecting External 1 or External 2 on your video monitor or projector.
CD
Player
Audio Cassette Deck
Video Cassette Recorder
TV Monitor
Laser Disc Player
Audio
Video
Audio
Video
L
L
L
L
L
L
LD Play
R
R
R
R
R
R
Audio Out
Audio Out
Video Out
Video In
Line Out
Rec/In
Play/Out
Rec/In
Video In
Play/Out
Video Out
Discrete 5.1 Adapter
Monitor
Video 4 Rec Video 4 Play
Video 3 Play Video 2 Play Video 1 Play
Monitor
Video 4 Rec Video 4 Play Video 3 Play Video 2 Play Video 1 Play
Comp
S
Video Video
PARASOUND P/SP-1500
AV Processor / Preamplifier
Parasound Products, Inc
San Francisco, CA U.S.A.
AC 120V 60Hz
Video
Audio 3
Audio 2
Audio 1
Video 4 Rec Video 4 Play
Video 3 Play Video 2 Play Video 1 Play
Rec Output
Rear
Center
Front/Direct
R
L
L
External
Remote
Input
DC Trigger
Center
Speaker
Sub Control
+12V GND
L C R full range
Sub off
None
Small
L C R full range
Sub full range
R
Large
or THX
L C R high pass
THX Filters
Subwoofer
Audio Inputs
Audio Outputs
Power Consumption 20 W
Notes:
Alternate Connection
1. If you are using amplifiers with different power ratings, use
the highest rated power amplifier for the center and subwoofer
channels. Use the next most powerful amplifier for the left and
right channels. Your smallest amplifier should be used for the
surround channels.
1
2
1
2
1
2
2. Connections from the video components to the P/SP-1500
show both S-video and composite video jacks. If the video
component you are connecting to the P/SP-1000 has both,
use only one type at a time.
Amplifier 1
Amplifier 2
Amplifier 3
3. For clarity, drawing does not show all possible connections.
4. Safety and patent information are on the bottom panel.
Left Speaker
Center Speaker
Right Speaker
Left Surround
Right Surround
Subwoofer
Powered Subwoofer
Input and Output Connections to the Parasound P/SP-1500
P/SP-1500 Owner's Manual
7
5.1 Outboard Adaptor Input Connection
The DB-25 connector on the rear panel of your P/SP-1500 will accept the processed analog output of an
outboard 5.1 digital adaptor such as the Parasound P/DD-1500 Digital Surround Processor (available Fall,
1996). With this advanced feature, you can play Dolby Digital AC-3 sources and keep up-to-date with the
latest advancements in digital surround and home theater technology.
Audio Output Connections
Front Left and Right Channel Outputs
Connect the left and right Front/Direct outputs of your P/SP-1500 to the inputs of the two channel
amplifier or multi-channel amplifier that will power your front left and right (L, R) speakers.
Center Channel Output
Connect the Center output of your P/SP-1500 to the input of the amplifier or the channel of a
multi-channel amplifier that will power your center (C) speaker.
Left and Right Surround Channel Outputs
Connect the left and right Rear outputs of your P/SP-1500 to the inputs of the two channel amplifier or
multi-channel amplifier that will power your left and right surround (LS, RS) speakers.
Subwoofer Output
Connect the Subwoofer output of your P/SP-1500 to the input of the power amplifier or channel of a
multi-channel amplifier that will power your subwoofer or to the line input of a powered subwoofer (Sub).
Audio Only Record/Play Connections
Use these outputs in conjunction with any of the audio inputs and an audio tape deck. Connect the left and
right Play/Output of your tape deck to the left and right input connectors of Audio 1, Audio 2 or
Audio 3. Next, connect the left and right Rec Output of your P/SP-1500 to the left and right Audio
Record/Input connectors of your tape deck.
Recording From Your P/SP-1500
You can use your P/SP-1500 for both audio/video and audio only recording with the Video 4 and Audio
Rec Output connections. To record through either of these recording output connectors, simply select the
source you want to record on the front panel or remote control and the P/SP-1500 simultaneously routes
the audio and video to the connectors of Video 4 Rec and to the audio connectors of Audio Rec Output.
Subwoofer Control Switch
The three position Subwoofer Control switch allows you to configure the subwoofer output jack to suit
your speaker system. If your front speakers are designed to run full range and you are not using a
subwoofer, set the Subwoofer Control switch to the L, C, R, Full Range/Sub off position. If your front
speakers are designed to run full range and you are using a subwoofer with a built in low-pass filter, set the
switch to the L, C, R, Full Range/Sub full range position. If you are using a THX-approved speaker
system that includes a subwoofer, set the switch to the L, C, R, Sub/THX Filters position. This activates
the built-in THX designed asymmetrical low pass and high pass crossover for the subwoofer and front left,
center, and right speakers. The low-pass filter for the subwoofer has a high frequency roll-off of 24 dB per
octave starting at 80 Hz. The high-pass filter has a low frequency roll-off of 12 dB per octave starting at
80 Hz for the front left, center, and right speakers.
8
P/SP-1500 Owner's Manual
Center Channel Speaker Selector
Set this rear panel switch to accommodate the type of center channel speaker you will be using.
Following are descriptions of the preferred center channel switch settings based upon the center speaker
you will be using.
Large or THX (Wide Band)
Switch to the Large or THX position for center channel speakers that have extended low bass capability
and can play as loud as your front left and right speakers without bass distortion. Use this setting for
THX Home Cinema center speakers. In this position, the P/SP-1500 routes the entire audio bandwidth
(20 Hz - 20 kHz) to the center channel output.
Small (Normal)
Switch to the Small position for smaller sized center channel speakers. In this position, the P/SP-1500
protects your center channel speaker from bass overload and distortion by diverting bass frequencies
below 100 Hz to the left and right channels. In this position, front channel imaging remains tonally
balanced even with the limited bass capability of a smaller center channel loudspeaker.
None (Phantom)
Switch to the None position if you do not have a center channel speaker. In this position, the front right
and left speakers share reproduction of the mono center channel signal to create a “phantom” image in
the center. However, without a good quality center channel speaker, you will be missing one of the key
benefits of Dolby Pro Logic and THX Cinema processing.
External Remote Control Input
The external infrared input works with many popular infrared repeater systems to allow for remote
control operation when infrared signals cannot directly reach the front panel receiver. The external
remote input connector is a standard 1/8 inch (3.5 mm) mini jack. Wire the tip for this plug positive and
the sleeve negative. Your Authorized Parasound Dealer or Custom Installer can recommend a
compatible repeater system for your P/SP-1500.
DC Trigger
This connector provides a +12 Volt DC 350 milliampere capacity trigger whenever you turn on the
P/SP-1500. Use this connector to activate equipment such as relays, rear screen projectors, motors for
film screens, power amplifiers or other components that can be triggered with DC voltage. You can also
use this DC Trigger connection to activate the two 15 Ampere relays in the optional Parasound SCAMP
Signal Controlled Amplifier Power automatic switching component. Contact your Parasound Dealer or
Custom Installer for more information about the SCAMP.
AC Line Cord Receptacle
The rear panel mounted IEC standard AC receptacle accepts an audiophile-grade AC cord supplied with
your P/SP-1500. Plug the female end of the AC cord firmly into the AC receptacle and make sure that it
is properly seated. Connect the male end directly to an AC wall outlet that is always "live" so that the
P/SP-1500 retains all its memorized settings. Avoid use of an extension cord or power strip since these
often degrade sound quality.
Infrared Sensor
Front Panel Display
B
O
Y
S
-
U
N
D
D
R
O
L
U
C
R
L
R
O
O
P
G
I
C
dB
R
L
C
p l i f i e r
P r o c e s s o r / P r e a m
A
S
F
I
L
M
L
U
V
P / S P - 1 5 0 0
A
SUB
RS
LS
Volume
Stereo
Dolby
THX
5.1
Audio
3
Audio
2
Audio
1
Video
4
Video
3
Video
2
Video
1
On-Off
Direct Pro Logic Cinema
Discrete
On Off Switch
Audio/Video Inputs
Audio Inputs
Primary Modes
Volume Control
Off
On
Mute
Off Mute and On Buttons
R-15
Cal
Input Level Calibration
and Trim Controls
Volume Controls
Input
Trim
Volume
Display
Delay
Delay and Display Buttons
Video 1
Video 4
Video 2
Audio 1
Video 3
Audio 2
Input Section
Mode Section
Audio 3
Hall
5.1 Ch
THX
Mono
Stereo
Direct
Ambiance
Pro Logic
P/SP-1500 Front Panel and Remote Control
10
P/SP-1500 Owner's Manual
Operating Your P/SP-1500
Refer to Diagram on Page 9
Using the Remote Control with On Screen and Front Panel Displays
The remote control included with your P/SP-1500 gives you complete access to all functions including
power, direct input selection, modes, volume, and calibration. The advanced on-screen and front panel
displays keep you informed of all of the various functions of the P/SP-1500.
On and Off Switches
There are separate On and Off remote control commands for the P/SP-1500 and a combined On-Off
button on the front panel. Press the On button to turn the unit on and press the Off button to turn it off.
When the P/SP-1500 is first turned on, the on-screen display shows the previously selected input, mode,
input level, and master volume level. At the same time, the front panel indicates the selected input, one
of three key processing modes, active channels, and master volume level. The on-screen status remains
on the screen for about four seconds. Whenever you turn on the P/SP-1500, it displays the source,
mode, and volume that were present when the unit was last turned off.
Off
On
Mute
R-15
Cal
Trim
Delay
Input
Volume
SOURCE
MODE
VIDEO 1
Display
Video
Video
1
4
THX CINEMA
Video
Audio
Hall
2
1
Video
Audio
3
2
dB
L
C
R
INPUT LEVEL - 3 dB
VOLUME - 28 dB
Audio
3
LS SUB RS
5.1 Ch
THX
Mono
Stereo
Direct
Stereo
THX
5.1 Ch
Dolby
Volume
Ambiance
Pro Logic
Direct Pro Logic Cinema Discrete
Mute
Press the mute button to completely interrupt the audio signal from reaching the output of the
P/SP-1500. When the mute function is engaged, Mute is displayed on the front panel and on-screen.
The mute button will not affect the Video 4 and Audio Rec output jacks.
Display
Pressing the Display button will show you the status of the P/SP-1500’s primary functions: selected
input, processing mode, input level, and master volume level. This display will remain on until you
press Display again or unless the unit is turned off. If there is no video source playing when you press
display, the P/SP-1500 shows the current status on a blue background. If a video source is playing, the
status appears over the video signal.
Off
On
Mute
R-15
Cal
Trim
Delay
SOURCE
MODE
VIDEO 1
Input
Volume
THX CINEMA
Display
Video 1
Video 4
INPUT LEVEL - 3 dB
VOLUME - 28 dB
Video 2
Audio 1
Video 3
Audio 2
Audio 3
Hall
5.1 Ch
THX
Mono
Stereo
Direct
Ambiance
Pro Logic
P/SP-1500 Owner's Manual
11
Volume
You can adjust the Volume from the remote control or on the front panel. The on-screen and front panel
displays indicate the volume level in decibels relative to THX Reference Level and all active channels will
flash for three about seconds each time you change the volume. The volume keys are also used in
conjunction with the Cal and Trim functions (see page 14 and 16).
Input Level Controls and Input Overload Indicator
These remote control adjustments limit the amount of signal sent to the surround processor from your
source components to maximize headroom. You can attenuate the Input level from its maximum of
0 dB to a minimum of -12 dB. Any time the input circuitry is being overdriven, the P/SP-1500 displays
Over on the front panel display and
in the upper right hand corner of the on-screen display any time
there is an overload. Set the Input level so the overload indicators flicker only with the highest peak
levels. If the Over indicators flash frequently, reduce the Input level accordingly.
Off
On
Mute
R-15
Cal
Trim
Delay
SOURCE
MODE
VIDEO 1
Input
Volume
THX CINEMA
Display
Video
Video
1
4
L
C
R
dB
INPUT LEVEL - 2 dB
Video
Audio
Hall
2
1
Video
Audio
3
2
LS SUB RS
Over
Audio
3
Stereo
THX
5.1 Ch
Dolby
Volume
5.1 Ch
THX
Mono
Stereo
Direct
Direct Pro Logic Cinema Discrete
Ambiance
Pro Logic
Input Selectors
You can select any of the seven inputs from the remote control or on the front panel. When you select an
input, a green LED on the front panel will illuminate corresponding to the selected input The
on-screen display will show the selected input, mode and input level.
Processing Modes
There are seven processing modes available with your P/SP-1500. All seven modes are accessible from the
remote control while the four most used processing modes are also accessible on the front panel.
Dolby Pro Logic
You can select the Dolby Pro Logic mode from the remote control or on the front panel. This mode
accurately decodes Dolby Surround encoded material to provide multi-channel playback including
dedicated center and surround channels. Most video releases of major movies and many television
programs, compact discs and video games are Dolby Surround encoded. You may use the Dolby Pro
Logic mode on a wide variety of non-encoded material with good results. Most stereo recordings will
produce surround effects to varying degrees, and center channel signals such as vocals will emanate more
naturally from the center channel. All output channels are operative in this mode.
THX Cinema
When you select the THX Cinema mode on the front panel or remote control, the P/SP-1500 engages
proprietary Lucasfilm circuitry along with Dolby Pro Logic processing. These THX processing circuits
include re-equalization, timbre matching, and de-correlation. THX Cinema processing greatly enhances
the film experience by equalizing excess treble mixed into many soundtracks and optimizing the
performance of surround speakers. If you are using THX Home Cinema speakers, you will probably want
to engage the THX Cinema mode for the playback of most film soundtracks. You can choose the THX
Cinema mode from either the remote control or on the front panel.
12
P/SP-1500 Owner's Manual
Stereo Direct
For critical listening, the Stereo Direct mode engages a precision bypass relay to route the selected input
source around all the surround processing circuitry of the P/SP-1500 and directly to its preamp section. As
a result, only the front left, right and subwoofer channels are active in the Stereo Direct mode. You can
select this mode from the remote control or on the front panel.
Hall
The Hall mode simulates the reverberant sonic characteristics of a concert hall. This mode enhances both
classical and rock music recordings. You can select the Hall mode only from the remote control. All
channels are operative in this mode.
Ambiance
The Ambiance mode adds a sense of spaciousness from the surround channels without any processing of
the front left and right channels. You can select the Ambiance mode only from the remote control. All
channels except center are operative in this mode. The ambiance mode is designed primarily as a subtle
enhancement to music rather than films.
Mono
When you select the Mono mode, the P/SP-1500 routes the summed left and right signals to the center and
subwoofer channels only. This mode works well for classic films, and older mono music recordings. If you
have the rear panel center speaker selected to the None position, the mono signal will appear in the front left
and right speakers to form a phantom image.
5.1 Discrete
When you select the 5.1 Discrete mode, the P/SP-1500’s output circuitry “looks” to the DB-25 connector
on its rear panel for analog signals decoded from a digital 5.1 outboard processor. There is an expanding
library of films available that are encoded in either Dolby Digital (AC-3) or DTS (Digital Theater Sound).
We designed the Parasound P/DD-1500 Dolby Digital (AC-3) processor (available Fall, 1996) specifically
to connect to this input. Be aware that if you have not connected a compatible outboard processor to the
DB-25 input, there will be no output from the P/SP-1500 when you select the 5.1 Discrete mode. You can
select the 5.1 mode from the remote control or on the front panel.
Storing Input Levels and Modes to Specific Inputs
For ease of operation, you can program the P/SP-1500 to memorize the input level and mode for a specific
input. For example, you may want your laser disc player connected to Video 1 to automatically be activated
in the THX Cinema mode with an input level of -3 dB each time this input is selected. You can use either
the remote control or front panel to memorize the input level and mode for a given input. Simply set the
desired input level and select the mode you want to store, then hold down the source select input button
where you want it stored until the word MEMORIZE flashes within the on-screen display. When MEMORIZE
stops flashing after three seconds, the P/SP-1500 has stored the input level and mode for the input displayed
on the screen. Whenever you return to a programmed input, the P/SP-1500 recalls its memorized input
level and mode.
Off
On
Off
On
Mute
Off
On
Mute
Mute
Cal
Trim
Delay
Cal
Trim
Delay
Cal
Trim
Delay
SOURCE
MODE
VIDEO 1
Input
Volume
Input
Volume
Input
Volume
Display
Display
Display
THX CINEMA
Video
Video
1
4
Video
Video
1
4
Video
Video
1
4
Video
Audio
Hall
2
1
Video
Audio
3
2
Video
Audio
Hall
2
1
Video
Audio
3
2
Video
Audio
Hall
2
1
Video
Audio
3
2
INPUT LEVEL - 3 dB
Audio
3
Audio
3
Audio
3
5.1 Ch
THX
Mono
5.1 Ch
THX
Mono
5.1 Ch
THX
Mono
Stereo
Direct
Stereo
Direct
Stereo
Direct
Ambiance
Pro Logic
Ambiance
Pro Logic
Ambiance
Pro Logic
MEMORIZED
3
Hold down input
2
DownSloealedctfmroomde Www.Somanuals.com. All Manuals Search And Download.
1
Set input level
P/SP-1500 Owner's Manual
13
Surround Channel Delay
The surround delay circuitry allows you to choose the amount of time it takes sound from the surround
channel speakers to follow the sound from the front left, right, and center speakers. This establishes the
precedence effect for the front channel speakers and helps you associate the sound with the image on the
screen rather than from behind you. (The precedence effect is how our hearing tends to identify or
localize sounds that we hear first when being subjected to a number of similar sounds coming from all
around us.) You can set the Delay time in 5 millisecond intervals from 15 to 30 milliseconds. Although
the recommended delay time for Dolby Pro Logic is 20 milliseconds, you can use the remote control to
adjust the delay time to best suit your listening room. The front panel and on-screen display both
indicate the amount of surround delay time. Use the chart below to best select the surround delay time
for your system.
Off
On
Mute
R-15
Cal
Trim
Delay
Input
Volume
SOURCE
MODE
VIDEO 1
THX CINEMA
20MS
Display
Video
Video
1
4
Video
Audio
Hall
2
1
Video
Audio
3
2
L
C
R
DELAY
Audio
3
LS SUB RS
mS
5.1 Ch
THX
Mono
VOLUME
- 28 dB
Stereo
Direct
Stereo
THX
5.1 Ch
Dolby
Ambiance
Pro Logic
Volume
Direct Pro Logic Cinema Discrete
25 ms 20 ms
15 ms
40
15 ms
35
30
25
15 ms
15 ms
10 ms
5 ms
20
15
Differential
Arrival Time
10
Preferred
5
0
Acceptable
Not Recommended
0
5
10
15
20
25
30
35
40
Distance from listening area to front speakers (feet)
XX ms
Useable speaker placement range with
delay time
14
P/SP-1500 Owner's Manual
Calibrating Your Home Theater System
Calibration involves independently adjusting the output level for each of the six channels of your
P/SP-1500 to accommodate different types of speakers and their placement variations. System
calibration is critical for optimum performance of your home theater. The P/SP-1500’s front panel and
on-screen display make system calibration very easy to perform. Since the only way to adjust individual
channel levels properly is from your listening/viewing position, the calibration controls are only
accessible from the remote control.
The most objective way to calibrate your system is with a sound pressure level (SPL) meter such as the
Realistic Sound Level Meter (catalog # 33-2050) available from Radio Shack stores in the USA for
around $30.00. If you use an SPL meter for calibration, hold it upright directly in front of your head
while you are seated in your listening area as you make adjustments. If an SPL meter is unavailable,
you can still adjust levels by ear with excellent results.
You can only perform system calibration from the remote control after selecting the Dolby Pro Logic
mode. Begin calibration by holding down the Cal button on the remote control while watching either
the front panel and/or on-screen display. Upon entering the Cal mode, the entire on-screen display
flashes CALIBRATE CH LEVELS and will also show individual channels and their decibel levels. The
master level will also automatically change to 0 dB to represent the THX reference level.
After four seconds, the blue background of the on-screen display will change to red, and you will hear
the "pink noise" test tone in the left channel to signal the beginning of the calibration cycle. The letter
L will also flash on-screen and on the front panel. As you continue to press the Cal button, the test
signal and displays will advance in the order of L, C, R, LS, RS, AND SUB. Advance through the
individual channels by sequentially pressing the Cal button.
Adjust each channel level with the volume buttons on the remote control until each speaker plays at the
same apparent loudness. (This is where the SPL meter comes in very handy.) As you press the volume
up or down button, the decibel levels in the on-screen and the front panel displays will change in 1 dB
increments for the channel that is flashing.
You complete the calibration sequence after adjusting the subwoofer by pressing Cal once again. You
will automatically exit from the calibration mode and the screen will return to normal. When you press
the Cal button any time after calibration, the P/SP-1500 displays your six original calibrated levels along
with acknowledgment of calibration with the word MEMORIZED. This calibration recall feature allows
you to return to your calibrated levels if you suspect that individual channels have been changed.
Once you have completed the calibration procedure, record your individual calibrated channel levels
here for future reference in case your P/SP-1500 loses AC power for over 24 hours.
CALIBRATE CH LEVELS
CALIBRATE CH LEVELS
L
C
R
L
C
R
___dB
___dB
___dB
___dB
___dB
___dB
LS
SUB
RS
LS
SUB
RS
___dB
___dB
___dB
___dB
___dB
___dB
Date _______
Date _______
P/SP-1500 Owner's Manual
15
Off
On
Off
On
Mute
Mute
R-15
R-15
Cal
Trim
Delay
Cal
Trim
Delay
Input
Volume
Input
Volume
Display
Display
CALIBRATE CH LEVELS
Video 1
Video 4
Video 1
Video 4
L
C
R
Video 2
Audio 1
Video 3
Audio 2
Video 2
Audio 1
Video 3
Audio 2
0 dB
0 dB
0 dB
Audio 3
Audio 3
L
C
R
dB
LS SUB RS
LS
0 dB
SUB
0 dB
RS
0 dB
Hall
5.1 Ch
THX
Mono
Hall
5.1 Ch
THX
Mono
Stereo
Direct
Stereo
Direct
Ambiance
Pro Logic
Ambiance
Pro Logic
Stereo
THX
5.1 Ch
Dolby
Volume
Direct Pro Logic Cinema Discrete
CALIBRATE CH LEVELS Flashes
Select Dolby Pro Logic on remote or front panel
Hold Cal button
for 3 seconds
1
2
3
Off
On
Mute
R-15
Cal
Trim
Delay
Input
Volume
Display
CALIBRATE CH LEVELS
Video 1
Video 4
L
C
R
Video 2
Audio 1
Video 3
Audio 2
0 dB
0 dB
0 dB
Audio 3
L
C
R
dB
LS SUB RS
LS
0 dB
SUB
0 dB
RS
0 dB
Hall
5.1 Ch
THX
Mono
Stereo
Direct
Ambiance
Pro Logic
Stereo
THX
5.1 Ch
Dolby
Volume
Direct Pro Logic Cinema Discrete
Screen turns red and L Flashes on-screen and front panel
Set channel levels
with Volume buttons
5
4
Off
On
Mute
R-15
Cal
Input
Volume
Trim
Display
Delay
CALIBRATE CH LEVELS
CALIBRATE CH LEVELS
Video 1
Video 4
L
C
R
L
C
R
Video 2
Audio 1
Video 3
Audio 2
0 dB
0 dB
0 dB
0 dB
0 dB
0 dB
Audio 3
LS
0 dB
SUB
0 dB
RS
0 dB
LS
0 dB
SUB
0 dB
RS
0 dB
Hall
5.1 Ch
THX
Mono
Stereo
Direct
Ambiance
Pro Logic
MEMORIZED
Press Cal to advance to next channel
After adjusting last channel (SUB)
screen shows MEMORIZED and
returns to normal
7
6
16
P/SP-1500 Owner's Manual
Using the Trim Function for Temporary Level Adjustment
If you want to temporarily adjust the individual levels of any channel for a particular soundtrack or
recording, use the Trim button on the remote control. For example, you may want to boost your
subwoofer or surround levels for a particular soundtrack without having to change the levels back when
you play your next selection.
The Trim function works in much the same way as the calibration function. Since the Trim function is
designed to let you make adjustments "on-the-fly", the on-screen display is superimposed on the picture
you are viewing instead of turning the screen blue or red. Begin adjusting levels by holding down the
Trim button on the remote control while watching either the front panel and/or on-screen display.
Upon entering this mode, the on-screen display flashes TRIM LEVELS. It also displays the individual
channels and their decibel levels. At the same time, the master level changes to 0 dB to represent THX
reference level and the letter L will flash on-screen and on the front panel. As you continue to press the
Trim button, the displays will advance in the order of L, C, R, LS, RS, AND SUB. Advance through the
individual channels by sequentially pressing the Trim button. Adjust the channel level with the volume
buttons on the remote control to suit your tastes. As you press the volume up or down button, the
decibel levels in the on-screen and the front panel displays will change in 1 dB increments for the
channel that is flashing.
Once you have finished the Trim sequence after adjusting the subwoofer (if desired), press Trim again.
You will automatically exit from the Trim mode and the screen will return to normal. Since the trim
function is temporary, if you change inputs, modes, or turn the P/SP-1500 off, the individual channel
levels will automatically return to the settings memorized during calibration.
Off
On
Off
On
Mute
Mute
R-15
R-15
Cal
Trim
Delay
Cal
Trim
Delay
Input
Volume
Input
Volume
Display
Display
TRIM LEVELS
Video 1
Video 4
Video 1
Video 4
L
0 dB
C
0 dB
R
0 dB
Video 2
Audio 1
Video 3
Audio 2
Video 2
Audio 1
Video 3
Audio 2
Audio 3
Audio 3
LS
0 dB
SUB
0 dB
RS
0 dB
Hall
5.1 Ch
THX
Mono
Hall
5.1 Ch
THX
Mono
Stereo
Direct
Stereo
Direct
Ambiance
Pro Logic
Ambiance
Pro Logic
Hold Trim button until TRIM LEVELS and L flashes
Adjust level with
Volume buttons
2
1
Off
On
Mute
R-15
Cal
Input
Volume
Trim
Display
Delay
TRIM LEVELS
TRIM LEVELS
Video 1
Video 4
L
C
R
L
C
R
0 dB
Video 2
Audio 1
Video 3
Audio 2
0 dB
0 dB
0 dB
0 dB
0 dB
Audio 3
LS
0 dB
SUB
0 dB
RS
0 dB
LS
0 dB
SUB
0 dB
RS
0 dB
Hall
5.1 Ch
THX
Mono
Stereo
Direct
Ambiance
Pro Logic
Press Trim to advance to next channel
After adjusting last channel (SUB)
screen returns to normal
4
3
P/SP-1500 Owner's Manual
17
Maintaining Your P/SP-1500
Your P/SP-1500 requires no periodic maintenance and has no user serviceable parts inside. To avoid the
risk of electric shock do not remove the top cover. Clean the chassis with a soft cloth moistened only with
Windex or clear water. Never use solvents or abrasives.
Remove the two AA batteries from the remote control if you do not plan to use it for an extended period.
Remove the battery cover annually to inspect and remove leaking batteries.
P/SP-1500 Troubleshooting Guide
No Power
Make sure the AC cord is properly seated in the IEC AC receptacle on rear panel.
No Output to One or All Channels
Make sure that P/SP-1500 indicators are on.
Check interconnects to power amplifier(s).
Check power amplifier(s).
Check channel levels with Trim or Cal buttons on remote control.
Hum in Speakers
Check for a grounding problem with the cable TV system; call your cable operator.
Consider installing a cable isolation device such as the Video Link #634 or the Mondial Magic
No Output to Surround Channels
Make sure that source playing is in stereo; processor cannot derive surround channels from mono signals.
No Center Channel Output
Make sure the Center Speaker switch on the rear panel is not set to the None position.
No Sub Channel Output
Make sure the Sub Control switch on the rear panel is not in the Off position.
Lights on Front Panel are Working, but No Response Via Remote or Front Panel.
The microprocessor "brain" within P/SP-1500 may have “locked up” due to an AC voltage spike.
Remove power cord from outlet for 30 seconds and plug back in.
Audio Present, but No Video Output
Make sure that composite or S-video output connections are consistent with inputs. See Page 6
Check video source
Try another video source.
No On-screen Display
Check monitor or projector connections.
Loses Memorized Settings
Check to make sure that AC outlet is always live and not switched off.
18
P/SP-1500 Owner's Manual
Remote Control Won't Work
Check batteries
Check for front panel operation to verify problem is not with P/SP-1500
DC Trigger Won't Activate Other Components
Check voltage at connector with DC voltmeter
Make sure other components do not require voltage exceeding +12 Vdc or current exceeding 350 mA
If All Else Fails
If you cannot get your P/SP-1500 to operate properly after referring the troubleshooting guide, call your
Parasound dealer or Parasound Technical Service. We can suggest other diagnostic tests you can easily
perform. If we determine that your P/SP-1500 should be returned to Parasound or an Authorized
Parasound Warranty Center for inspection and possible servicing, call for the location of a warranty
center near you. If you choose to send it to Parasound, contact us to obtain a Return Authorization (RA)
number. You will be asked to re-pack the unit in its original packaging plus an additional outer box for
protection during transit. The Return Authorization number must be clearly marked on the outer carton
only. You should ship the unit by UPS with adequate insurance. You must also include a copy of your
purchase receipt to validate your ownership.
Units that arrive without your specific Return Authorization number, without a suitable shipping carton
or evidence of improper internal packing must be refused. We do not accept collect shipments. After
repair under warranty, the unit will be returned to you via prepaid UPS. In the case of an out of warranty
repair, contact us and we will advise you of the repair charges before you ship the unit to us. The same
packing and Return Authorization requirements apply.
Notes:
P/SP-1500 Owner's Manual
19
P/SP-1500 Specifications
Dolby Pro Logic/THX Cinema
Preamp Direct
Audio Section
Frequency Response
Front
Rear
Center (Small)
Center (Large or THX)
Subwoofer
12 Hz-60 kHz
500 Hz-6.5 kHz
200 Hz-60 kHz
12 Hz-60 kHz
10 Hz-80 Hz
10 Hz-100 kHz
10 Hz-80 Hz
< 0.01 %
< 0.15 %
200 mV
Harmonic Distortion
Front
Center
Rear
Subwoofer
< 0.06 %
< 0.06 %
< 0.6 %
< 0.15 %
Input Sensitivity
All Channel Inputs
200 mV
Input Impedance
All Inputs
47 kΩ
47 kΩ
IM Distortion
(1 kHz 1V Output)
All Channels
< 0.06 %
< 0.01 %
Signal/Noise Ratio
(Flat/A-Weighted)
Front
Center
Rear
78 dB / 92 dB
78 dB / 92 dB
78 dB / 85 dB
78 dB / 92 dB
85 dB / 100 dB
85 dB / 100 dB
Subwoofer
Video Section
(Output 1 V / 75 Ω Load)
Sensitivity
Frequency Response
Overload
1 V + /- 1 dB
0.3 MHz -10 MHz + /- 1 dB
1.4 V
Dimensions
19" wide x 3 1/2" high x 13" deep 4 1/8" high with feet
Weight
16 lb
Power Requirements
110 V - 120 V 60 Hz AC, 19 W; may be rewired for 220 V - 240 V, 50 Hz
20
P/SP-1500 Owner's Manual
Special Features
• Four Audio/Video Inputs
• Audiophile IEC AC Cord
• Seven Processing Modes
• Rear Panel Infrared Input
• On-Screen Display
• Automatic Bypass Direct Output
• Adjustable Surround Delay Times
• 32,000 µF Main Power Supply
• Precision Resistors and Capacitors
• Silver Plated Internal Wiring
• Preamp Direct Circuitry
• Gold Clad Precision Bypass Relays
• Center Speaker Selector (Phantom)
• Heavy Duty Two Rack Space Chassis
• Lucasfilm THX Certified
• 5.1 Discrete Upgradeability
• Built-in Asymmetrical Crossover
• Calibrated Level Memory
• Relay Switched S-Video Capability
• High Current Audio Section
• External Infrared Input
• Independent Regulated Power Supplies
• Selectable Center Channel Operation
• Analog Pro Logic Processing
Specifications and features subject to change without notice
P/SP-1500 Owner's Manual
21
Parasound Limited Warranty (USA only)
Your Parasound P/SP-1500 is covered by a limited warranty against defects in materials and
workmanship for a period of two years from date of purchase. This warranty is provided by the
Parasound dealer where the unit was purchased. Warranty repair will be performed only when a copy of
your purchase receipt is presented to validate your ownership, date of purchase and authorized status of
the selling dealer. Defective parts will be repaired or replaced without charge by your authorized
dealer’s store or the location designated by your dealer that is authorized to service Parasound
equipment. Additional information is available by calling or writing to the Service Manager, Parasound
Products, Inc. at the address below. Charges for unauthorized service and transportation costs are not
reimbursable under this warranty.
This warranty becomes void if the product has been damaged by alteration, misuse, accident or neglect.
Alteration includes any removal or defacement of its serial number. This warranty
becomes void if unit has been connected or operated contrary to printed instructions. The warrantor
assumes no liability for property damage or any other incidental or consequential damage whatsoever
which may result from the failure of this product. Any and all warranties of merchantability and fitness
implied by law are limited to the duration of this expressed warranty.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitations
may not apply to you. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which vary state by
state.
Manufactured under license from Lucasarts Entertainment Company. U.S. and foreign patents pending.
Lucasfilm Audio and Home THX are trademarks of Lucasarts Entertainment Company, Lucasfilm is a trademark
of Lucasfilm Ltd.
This unit is manufactured under license from Dolby Laboratories Licensing Corporation. "Dolby",
"Pro Logic", and the double-D symbol are trademarks of the Dolby Laboratories Licensing Corporation.
affordable audio for the critical listener
Parasound Products, Inc. 950 Battery Street, San Francisco, CA 94111
415-397-7100 / FAX 415-397-0144
© 1996 Parasound Products, Inc.
Rev. B
|
Miele Dishwasher G 4570 User Manual
Milan Technology Switch MIL S8000G User Manual
Mr Coffee Coffeemaker PR12A User Manual
Multi Tech Systems Network Router MT5600BA V90 User Manual
NETGEAR Switch GS700TP 724TP User Manual
Nikon Photo Scanner FH 869G User Manual
Omnimount TV Mount OM10327 User Manual
OPTI UPS Power Supply GS1100B User Manual
Optoma Technology Projector TW695UT3D User Manual
Panasonic Network Card 2SA2021G User Manual